How Flashing Mobile Phone Motorola
8 October, 2011 | Mobile Phones | 0 Commentdriveruniversal.info. How Flashing Mobile Phone Motorola.
Flashing is the process of writing a new firmware (OS) to replace the old firmware. To modify the ROKR E2 Firmware flashing is the first step, as well as the most dangerous. Because in case of a mistake while flashing will result in fatal error. But don’t worry, I’m sure all E2 can be flashed. perfectly if followed all the steps that are written. Oh yeah, keep in mind that the E2 will not die because of flash, if it fails to flash and totally off, any easy way to cure it, i.e. by repeating the process of flashing.
To do flashing, you need software RSD Lite 2.8 to over, drivers and firmware itself. For equipment, such as data cables, already available in the sales package. PC not necessary need a sophisticated, provided that adequate enough with OS Windows XP only. For those using Windows Vista, you need the latest drivers for Vista.
You can use the RSD Lite version 2.8. I suggest using version 3.0 or later, I’m now using version 4.x. already have all the software on? (use Google to find the RSD Lite), If already, then you are ready to do flashing. Here are the steps that are required:
How to Flashing Mobile phone Motorola ??
1. make sure your cell phone battery in full. REMEMBER!! If your cell phone battery is not full, then it is likely a flash process will be stalled in the middle of the road. If that happens, You will be E2 died (died) for a while. So if that happens, you must charge until full again and repeat the flash. There is a possibility you will need another or charge sat E2 (frog) to conduct charge. So always keep in mind, the batteries must be in their full.
2. Extract the drivers and firmware. Remember well the storage that is easily searched.
3. turn off your cell phone, then hold down the voice (on the right side of the phone, above the keylock) and power button simultaneously. You will be taken to the bootloader, here we refer to it as the AP or more easy bootloader first. After a while, press the voice again and you’ll be carried away to the next the bootloader (see appearance has changed, if not, press the button until voice change), which
also called BP or simply the second bootloader. Well, you need to take note that:
a. AP or first used for the bootloader flash files have a .dit extension. sbf and hs.
b. BP or the second bootloader used for flash files have a .dit extension. shx
4. open the folder that you extract the firmware, you usually find one file and one file shx. sbf. Well, in this situation, You need to do a flash file. shx first. When you’re finished, just continue with sbf. In short, flash BP was then AP. However, if only one file is found, then the sbf enough with flash AP only. Hs is the patch File to get a quad-band.
5. open RSD Lite, run the mobile phones in the second bootloader or BP. Connect Your PC and HP E2 with a data cable. Use the backports USB on your PC for better results. Windows will detect the new hardware and drivers. Follow these steps when the new hardware found window appears:
a. Windows will prompt you to connect to the internet, select No.
b. Then Windows will ask you to do a “search drivers automatically”, do not select that option, choose “No, I will choose …”.
c. Next you’ll see the option to search the drive a:\ or
d:\, disregard it , and then select an option under “include this …”, click “Browse” and navigate to the folder where the drivers are stored. Click ok and the search will start and will continue on a window that shows the installation of the driver, if the question comes up, click “Continue anyway”. Wait until finished.
d. Repeat the same steps for some of the other drivers. SIP
6. If the driver is already installed, RSD Lite will detect your phone. After that, browse Your firmware file, in this situation, look for the shx. Click start, the flash process will begin. Wait until finished, RSD Lite will ask you to “please manually turn on the phone”, then unplug your mobile phone and turn it off by removing the battery and then install it again, turn on as usual. Connect the cable data, again with the RSD Lite status will change to “PASS. Finished. ”
7. follow step number 5 and 6, this time with a bootloader first/AP and sbf smpai completed file (PASS)
Easy isn’t it? not to skip the first step, because that’s the most important step. No need to hurry, You can make it! If you find one file then just need only sbf flash once. Hs flash File. it needs also.
Some of the positive things that you will get after the flash Firmware:
1. a more toned Voice output.
2. Interface is faster.
3. compatible with file mpkg (Linux)
4. unable to retrieve the latest multimedia, such as file2. avi flv 3gp etc…
5. in a number of the firmware, allowing you to extract a zip file archive. rar, read and. script Linux, opens a text file with the browser Opera 8.5, and much more.
That is flashing mobile phone and hopefully can help how flashing mobile phone motorola.
Tagged with: flash motorola, flashing mobile phone, how to flash, mobile flash
